cisco交換機開啟dhcp服務
阿新 • • 發佈：2017-08-01
cisco、dhcp
拓撲圖如下：
上述設備用途說明：
1、使用R1做dhcp server
2、使用R2和R3代替電腦做dhcp client
3、SW1用做傻瓜交換機。
dhcp server配置（R1配置）：
R1#disable #############使用 disable 命令退出特權模式 R1> R1>enable #############使用 enable 命令進入特權模式 R1#show privilege Current privilege level is 15 #############查看特權模式的級別 ############# 進入配置模式 R1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R1(config)#exit #############查看接口狀態 R1#show ip interface brief Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 unassigned YES unset administratively down down Serial1/1 unassigned YES unset administratively down down Serial1/2 unassigned YES unset administratively down down Serial1/3 unassigned YES unset administratively down down R1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. #############進入接口進行配置 R1(config)#int fastEthernet 0/0 R1(config-if)#no shutdown R1(config-if)# *Aug 1 19:39:28.523: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Aug 1 19:39:29.523: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R1(config-if)#ip address 123.1.1.1 255.255.255.0 R1(config-if)# R1(config-if)# #############在配置模式中查看接口狀態需要加 do 前綴 R1(config-if)#do show ip interface brief Interface IP-Address OK? Method Status Protocol FastEthernet0/0 123.1.1.1 YES manual up up FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 unassigned YES unset administratively down down Serial1/1 unassigned YES unset administratively down down Serial1/2 unassigned YES unset administratively down down Serial1/3 unassigned YES unset administratively down down R1(config-if)# #############也可使用 end 命令退出配置模式 R1(config-if)#end R1# R1# *Aug 1 19:43:17.991: %SYS-5-CONFIG_I: Configured from console by console R1# R1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. #############開啟dhcp server 功能 R1(config)#service dhcp R1(config)#ip dhcp pool R123 R1(dhcp-config)#network 123.1.1.0 255.255.255.0 #############將客戶端的網關指向 dhcp server 接口的IP R1(dhcp-config)#default-router 123.1.1.1 #############將客戶端的DNS指向 dhcp server 接口的IP R1(dhcp-config)#dns-server 123.1.1.1 #############設置租期為1天0時1分 R1(dhcp-config)#lease 1 0 1 #############配置域名為cisco.com R1(dhcp-config)#domain-name cisco.com R1(dhcp-config)#
dhcp client配置（R2和R3配置）：
R2#configure terminal Enter configuration commands, one per line. End with CNTL/Z. #############禁用ip routing路由轉發表，將路由器模擬為pc R2(config)#no ip routing R2(config)#int fastEthernet 0/0 R2(config-if)#no shutdown R2(config-if)# *Aug 1 19:07:41.279: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Aug 1 19:07:42.279: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up #############開啟dhcp動態獲取 R2(config-if)#ip address dhcp R2(config-if)# *Aug 1 19:11:47.891: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0/0 assigned DHCP address 123.1.1.2, mask 255.255.255.0, hostname R2 R2(config-if)#end #############查看接口狀態 R2#show ip interface brief Interface IP-Address OK? Method Status Protocol FastEthernet0/0 123.1.1.2 YES DHCP up up FastEthernet0/1 unassigned YES unset administratively down down Serial1/0 unassigned YES unset administratively down down Serial1/1 unassigned YES unset administratively down down Serial1/2 unassigned YES unset administratively down down Serial1/3 unassigned YES unset administratively down down R2# #############查看單獨接口狀態 R2#show running-config interface fastEthernet 0/0 Building configuration... Current configuration : 94 bytes ! interface FastEthernet0/0 ip address dhcp no ip route-cache duplex auto speed auto end
本文出自 “甘木” 博客，請務必保留此出處http://ganmu.blog.51cto.com/9305511/1952781
cisco交換機開啟dhcp服務