華為OSPF、BGP路由反射器配置詳解

阿新 • • 發佈：2018-10-14

cost mas -o 技巧 ali 所有工程 moment pack

對於網絡工程師而言，OSPF、BGP的重要性不言而喻，本篇文章我們就來回顧下OSPF、BGP的配置技巧，重點如下
1.熟悉DHCP配置；
2.熟悉OSFP配置；
3.BGP路由反射器配置

入下圖所示，要求如下：
1.網絡拓撲規劃如圖所示；
2.PC1、PC2、PC3全部自動獲取ip地址；
3.R1、R2、R3之間運行osfp保證網絡的聯通性；
4.PC1、PC2、PC3之間網絡互通

技術分享圖片

第一步配置OSPF保證路由器直接網絡連通性
R1配置如下：
[R1]dhcp enable
Info: The operation may take a few seconds. Please wait for a moment.done.

[R1]interface g0/0/2
[R1-GigabitEthernet0/0/2]ip address 192.168.1.254 24
[R1-GigabitEthernet0/0/2]dhcp select interface
[R1]interface g0/0/0
[R1-GigabitEthernet0/0/0]ip address 192.168.12.1 24
[R1-GigabitEthernet0/0/0]q
[R1]interface LoopBack 0
[R1-LoopBack0]ip address 10.10.1.1 24
[R1-LoopBack0]q
[R1-ospf-1]area 0
[R1-ospf-1-area-0.0.0.0]network 192.168.12.0 0.0.0.255

[R1-ospf-1-area-0.0.0.0]network 10.10.1.1 255.255.255.255
R2配置如下：
[R2]dhcp enable
Info: The operation may take a few seconds. Please wait for a moment.done.
[R2]interface g0/0/2
[R2-GigabitEthernet0/0/2]ip address 192.168.2.254 24
[R2-GigabitEthernet0/0/2]dhcp select interface
[R2]interface g0/0/1
[R2-GigabitEthernet0/0/1]ip address 192.168.12.2 24.

[R2-GigabitEthernet0/0/1]q
[R2]interface g0/0/0
[R2-GigabitEthernet0/0/0]ip address 192.168.23.2 24.
[R2-GigabitEthernet0/0/0]q
[R2]interface LoopBack 0
[R2-LoopBack0]ip address 10.10.2.2 24
[R2-LoopBack0]q
[R2-ospf-1]area 0
[R2-ospf-1-area-0.0.0.0]network 192.168.12.0 0.0.0.255
[R2-ospf-1-area-0.0.0.0]network 192.168.23.0 0.0.0.255
[R2-ospf-1-area-0.0.0.0]network 10.10.2.2 255.255.255.255
R3配置如下：
[R2]dhcp enable
Info: The operation may take a few seconds. Please wait for a moment.done.
[R3]interface g0/0/2
[R3-GigabitEthernet0/0/2]ip address 192.168.3.254 24
[R3-GigabitEthernet0/0/2]dhcp select interface
[R3]interface g0/0/1
[R3-GigabitEthernet0/0/1]ip address 192.168.23.3 24
[R3]interface LoopBack 0
[R3-LoopBack0]ip address 10.10.3.3 24
[R3-LoopBack0]q
[R3-ospf-1]area 0
[R3-ospf-1-area-0.0.0.0]network 192.168.23.0 0.0.0.255
[R3-ospf-1-area-0.0.0.0]network 10.10.3.3 255.255.255.255
測試路由器直接連通性：
在R1上ping路由器R3，網絡互通
[R1]ping 10.10.3.3
PING 10.10.3.3: 56 data bytes, press CTRL_C to break
Reply from 10.10.3.3: bytes=56 Sequence=1 ttl=254 time=40 ms
Reply from 10.10.3.3: bytes=56 Sequence=2 ttl=254 time=20 ms
Reply from 10.10.3.3: bytes=56 Sequence=3 ttl=254 time=30 ms
Reply from 10.10.3.3: bytes=56 Sequence=4 ttl=254 time=30 ms
Reply from 10.10.3.3: bytes=56 Sequence=5 ttl=254 time=50 ms

--- 10.10.3.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 20/34/50 ms
第二步配置bgp
R1配置如下
[R1]bgp
[R1]bgp 64512
[R1-bgp]peer 10.10.2.2 as-number 64512
[R1-bgp]peer 10.10.2.2 connect-interface LoopBack 0
[R1-bgp]import-route direct
[R1-bgp]router-id 1.1.1.1
R2配置如下
[R2]bgp 64512
[R2-bgp]router-id 2.2.2.2
[R2-bgp]peer 10.10.1.1 as-number 64512
[R2-bgp]peer 10.10.1.1 connect-interface LoopBack 0
[R2-bgp]peer 10.10.3.3 as-number 64512
[R2-bgp]peer 10.10.3.3 connect-interface LoopBack 0
[R2-bgp]import-route direct
R3配置如下
[R3]bgp
[R3]bgp 64512
[R3-bgp]peer 10.10.2.2 as-number 64512
[R3-bgp]peer 10.10.2.2 connect-interface LoopBack 0
[R3-bgp]import-route direct
[R3-bgp]router-id 3.3.3.3
此時查看R1bgp路由表和R3的路由表如下;
bgp路由表
[R1]display bgp routing-table

BGP Local router ID is 1.1.1.1
Status codes: * - valid, > - best, d - damped,
h - history, i - internal, s - suppressed, S - Stale
Origin : i - IGP, e - EGP, ? - incomplete

Total Number of Routes: 12
Network NextHop MED LocPrf PrefVal Path/Ogn

> 10.10.1.0/24 0.0.0.0 0 0 ?
> 10.10.1.1/32 0.0.0.0 0 0 ?
>i 10.10.2.0/24 10.10.2.2 0 100 0 ?
> 127.0.0.0 0.0.0.0 0 0 ?
> 127.0.0.1/32 0.0.0.0 0 0 ?
> 192.168.1.0 0.0.0.0 0 0 ?
> 192.168.1.254/32 0.0.0.0 0 0 ?
>i 192.168.2.0 10.10.2.2 0 100 0 ?
*> 192.168.12.0 0.0.0.0 0 0 ?
- i 10.10.2.2 0 100 0 ?
  > 192.168.12.1/32 0.0.0.0 0 0 ?
  >i 192.168.23.0 10.10.2.2 0 100 0 ?
  [R3]dis ip routing-table
  Route Flags: R - relay, D - download to fib
  Routing Tables: Public
  Destinations : 18 Routes : 18

Destination/Mask Proto Pre Cost Flags NextHop Interface

  10.10.1.1/32  OSPF    10   2           D   192.168.23.2    GigabitEthernet

0/0/1
10.10.2.0/24 IBGP 255 0 RD 10.10.2.2 GigabitEthernet
0/0/1
10.10.2.2/32 OSPF 10 1 D 192.168.23.2 GigabitEthernet
0/0/1
10.10.3.0/24 Direct 0 0 D 10.10.3.3 LoopBack0
10.10.3.3/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.10.3.255/32 Direct 0 0 D 127.0.0.1 LoopBack0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.2.0/24 IBGP 255 0 RD 10.10.2.2 GigabitEthernet
0/0/1
192.168.3.0/24 Direct 0 0 D 192.168.3.254 GigabitEthernet
0/0/2
192.168.3.254/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
192.168.3.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
192.168.12.0/24 OSPF 10 2 D 192.168.23.2 GigabitEthernet
0/0/1
192.168.23.0/24 Direct 0 0 D 192.168.23.3 GigabitEthernet
0/0/1
192.168.23.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
192.168.23.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

可以總結如下，可以看到，由於IBGP 遵守水平分割規則，R2不能將學習到的路由互相轉發，造成R1與R3不能學習到對方的路由。PC1與PC2不能ping通。
在R2上配置路由反射器，使R1和R3成為了R2路由反射器配置如下
[R2]bgp 64512
[R2-bgp]peer 10.10.1.1 reflect-client
[R2-bgp]peer 10.10.3.3 reflect-client

R1的路由表和bgp路由表如下：
[R1]display bgp routing-table

BGP Local router ID is 1.1.1.1
Status codes: * - valid, > - best, d - damped,
h - history, i - internal, s - suppressed, S - Stale
Origin : i - IGP, e - EGP, ? - incomplete

Total Number of Routes: 14
Network NextHop MED LocPrf PrefVal Path/Ogn

> 10.10.1.0/24 0.0.0.0 0 0 ?
> 10.10.1.1/32 0.0.0.0 0 0 ?
>i 10.10.2.0/24 10.10.2.2 0 100 0 ?
>i 10.10.3.0/24 10.10.3.3 0 100 0 ?
> 127.0.0.0 0.0.0.0 0 0 ?
> 127.0.0.1/32 0.0.0.0 0 0 ?
> 192.168.1.0 0.0.0.0 0 0 ?
> 192.168.1.254/32 0.0.0.0 0 0 ?
>i 192.168.2.0 10.10.2.2 0 100 0 ?
>i 192.168.3.0 10.10.3.3 0 100 0 ?
*> 192.168.12.0 0.0.0.0 0 0 ?

i 10.10.2.2 0 100 0 ?
> 192.168.12.1/32 0.0.0.0 0 0 ?
>i 192.168.23.0 10.10.2.2 0 100 0 ?
[R1]dis ip ro
[R1]dis ip routing-table
Route Flags: R - relay, D - download to fib
Routing Tables: Public
Destinations : 20 Routes : 20

Destination/Mask Proto Pre Cost Flags NextHop Interface

  10.10.1.0/24  Direct  0    0           D   10.10.1.1       LoopBack0
  10.10.1.1/32  Direct  0    0           D   127.0.0.1       LoopBack0
10.10.1.255/32  Direct  0    0           D   127.0.0.1       LoopBack0
  10.10.2.0/24  IBGP    255  0          RD   10.10.2.2       GigabitEthernet

0/0/0
10.10.2.2/32 OSPF 10 1 D 192.168.12.2 GigabitEthernet
0/0/0
10.10.3.0/24 IBGP 255 0 RD 10.10.3.3 GigabitEthernet
0/0/0
10.10.3.3/32 OSPF 10 2 D 192.168.12.2 GigabitEthernet
0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.1.0/24 Direct 0 0 D 192.168.1.254 GigabitEthernet
0/0/2
192.168.1.254/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
192.168.1.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
192.168.2.0/24 IBGP 255 0 RD 10.10.2.2 GigabitEthernet
0/0/0
192.168.3.0/24 IBGP 255 0 RD 10.10.3.3 GigabitEthernet
0/0/0
192.168.12.0/24 Direct 0 0 D 192.168.12.1 GigabitEthernet
0/0/0
192.168.12.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
192.168.12.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
192.168.23.0/24 OSPF 10 2 D 192.168.12.2 GigabitEthernet
0/0/0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0

可以總結看到，路由反射器將從客戶處學到的路由轉發給除此客戶外的所有的客戶，R1與R3可以學習到對方的路由。PC1與PC3可以ping通。
測試PC1、PC2、PC3網絡互通
PC>ping 192.168.3.253

Ping 192.168.3.253: 32 data bytes, Press Ctrl_C to break
From 192.168.3.253: bytes=32 seq=1 ttl=125 time=31 ms
From 192.168.3.253: bytes=32 seq=2 ttl=125 time=32 ms
From 192.168.3.253: bytes=32 seq=3 ttl=125 time=31 ms
From 192.168.3.253: bytes=32 seq=4 ttl=125 time=15 ms
From 192.168.3.253: bytes=32 seq=5 ttl=125 time=32 ms

配置成功！！！！

華為OSPF、BGP路由反射器配置詳解

cost mas -o 技巧 ali 所有工程 moment pack 對於網絡工程師而言，OSPF、BGP的重要性不言而喻，本篇文章我們就來回顧下OSPF、BGP的配置技巧，重點如下1.熟悉DHCP配置；2.熟悉OSFP配置；3.BGP路由反射器配置入下圖所示，要求如

華為OSPF、BGP路由反射器配置詳解

華為OSPF、BGP路由反射器配置詳解

華為PAT端口地址映射配置詳解（一）

華為PAT端口地址映射配置詳解（二）

華為PAT端口地址映射配置詳解（三）

BGP路由反射器以及大AS之間的鄰居建立

華為防火墻BGP路由

華為設備BGP路由技術

Rsync同步服務器配置詳解

webpack4 css打包、壓縮、分離、去重等優化配置詳解

阿里雲API閘道器配置詳解

shell指令碼之正則表示式、函式、grep、sed、awk、printf等基本命令配置詳解

linux squid代理服務器配置詳解

Linux /centOS7 Samba服務器配置詳解

cent OS7搭建vsftp服務器配置詳解

centOS7搭建DNS服務器配置詳解

《深入淺出 —— BGP鄰居、聯盟、路由反射器綜合配置》

華為OSPF動態路由原理

華為OSPF動態路由實戰

華為DHCP、ACL、RIP、獨臂路由匯總小實驗

BGP（二）——聯盟&路由反射器

華為OSPF、BGP路由反射器配置詳解

相關推薦