arduino IDE 自帶示例中的Basics系列，

可以說是

向一個擁有C系家族編程語言基礎的人

解釋清楚了它自己的基本操作

BareMinimum（基本文件結構）：

void setup() {
  // put your setup code here, to run once:
  // 這裏放的setup代碼只會運行一次
}

void loop() {
  // put your main code here, to run repeatedly:
  // 這裏放的主要代碼會在setup之後不停循環執行
}

Start（有修改）：

// the setup routine runs once when you press reset:
 
//setup會在你按下reset之後首先執行
void setup() {                
  // initialize the digital pin as an output.
  // 將數字端口初始化為輸出模式
  pinMode(0, OUTPUT); //LED on Model B
  pinMode(1, OUTPUT); //LED on Model A  or Pro
}

// the loop routine runs over and over again forever:
//loop會一遍又一遍的永遠執行下去
void loop() {
  digitalWrite(0, HIGH);   //
 
 turn the LED on (HIGH is the voltage level)
                                    // 打開LED（HIGH代表電壓高低）
  digitalWrite(1, HIGH);
  delay(1000);               // wait for a second
  digitalWrite(0, LOW);    // turn the LED off by making the voltage LOW
                                    // 將電壓降低來關閉LED
  digitalWrite(1
 
, LOW); 
  delay(1000);               // wait for a second
}

Blink：

/*
  Blink
  閃爍

  Turns an LED on for one second, then off for one second, repeatedly.
  點亮LED持續1秒鐘，然後熄滅LED一秒鐘，一次循環。

  Most Arduinos have an on-board LED you can control.
  許多arduino都有一個板載LED可供使用

  On the UNO, MEGA and ZERO it is attached to digital pin 13, on MKR1000 on pin 6.
  在UNO，MEGA和ZERO上它與數字端口13相連。//後略

  LED_BUILTIN is set to the correct LED pin independent of which board is used.
  LED_BUILTIN被設定為各種主板相對應的LED而與型號無關。
  
  If you want to know what pin the on-board LED is connected to on your Arduino  model, check the Technical Specs of your board at:
  如果你想知道你的這種arduino上到底哪個端口連接著板載LED，那麽查看詳細的說明可以到：
  https://www.arduino.cc/en/Main/Products

  modified 8 May 2014
  by Scott Fitzgerald
  modified 2 Sep 2016
  by Arturo Guadalupi
  modified 8 Sep 2016
  by Colby Newman

  This example code is in the public domain.

  http://www.arduino.cc/en/Tutorial/Blink
*/

// the setup function runs once when you press reset or power the board
void setup() {
  // initialize digital pin LED_BUILTIN as an output.
  // 將LED_BUILTIN端口初始化為輸出模式。
  pinMode(LED_BUILTIN, OUTPUT);
}

// the loop function runs over and over again forever
void loop() {
  digitalWrite(LED_BUILTIN, HIGH);   // turn the LED on (HIGH is the voltage level)
  delay(1000);                       // wait for a second
  digitalWrite(LED_BUILTIN, LOW);    // turn the LED off by making the voltage LOW
  delay(1000);                       // wait for a second
}

以上的代碼皆可直接下載到UNO上運行

關於具體代碼的理解，

請各位善用自己的英語知識

與互聯網工具

本節關鍵代碼詞匯含義對照：

setup ≈ set up 意思非常之多，初始化，安排，安裝，構建，都可以

loop 循環

pin 端口/針腳，1pin就是一根線，所以電腦裏面的電源插口，4P，6P，24P就是這樣來的

built in 內置/板載

digital 數字，關於模擬和數字的區別，你用著用著就明白了

delay 等待/延遲

[arduino]-1-Basics代碼解讀