Linux 下 nohup 與 & 的聯絡
阿新 • • 發佈:2018-12-03
背景
一直沒搞清楚 nohup
與 &
的區別, 看著公司裡遺留的shell, 也就稀裡糊塗地用著... 這是很糟糕的態度
結論放前面
&
使程序在後臺執行, 預設輸出到標準輸出(即當前螢幕), 除非重定向輸出.
此時忽略 SIGINT 訊號.
==若關閉會話, 則程序會結束==
nohup
程序仍舊在前臺跑, 預設輸出到 nohup.out
.
此時程序忽略 SIGHUP 訊號, 關閉會話不影響程序.
==Ctrl+c
會使程序中斷==
nohup
+ &
程序在後臺跑, 忽略 SIGINT, SIGHUP 訊號.
測試
repeat=${1:-20}
echo 迴圈次數 $repeat
counter=0
while [ $counter -lt $repeat ]
do
echo 第${counter}次迴圈
let "counter ++"
sleep 1
done
echo 結束迴圈
直接執行
[[email protected] tmp]# sh test.sh
迴圈次數 20
第0次迴圈
第1次迴圈
第2次迴圈
^C
此時不論是直接 Ctrl+c
或 關閉當前ssh連線, 都會導致程序停止
[[email protected] tmp]# sh test.sh > test.out
^C
此時程序仍在前端跑, 檢視 test.out
檔案會發現在輸出, 此時不論是直接 Ctrl+C
或 關閉當前ssh連線, 都會導致程序停止
單獨使用 &
[[email protected] tmp]# sh test.sh & [1] 111418 [[email protected] tmp]# 迴圈次數 20 第0次迴圈 第1次迴圈 第2次迴圈 ^C [[email protected] tmp]# 第3次迴圈 第4次迴圈 第5次迴圈 ^C [[email protected] tmp]# 第6次迴圈 第7次迴圈 第8次迴圈 第9次迴圈 第10次迴圈 第11次迴圈
此時程序在後臺跑, 同時預設會輸出到螢幕上.
此時 Ctrl+c
無效, 即程序忽略了 SIGINT 訊號.
但若是直接關閉ssh連線(會話), 則該程序會被關閉, 這是因為程序受到了 SIGHUP 訊號影響.
系統對SIGHUP訊號的預設處理是終止收到該訊號的程序。所以若程式中沒有捕捉該訊號,當收到該訊號時,程序就會退出。
[[email protected] tmp]# sh test.sh > test.out &
[4] 111758
[[email protected] tmp]#
使程序在後臺跑, 輸出被重定向到指定檔案
可用 jobs -l
獲取當前的所有後臺程序
[[email protected] tmp]# jobs -l
[2]+ 113043 Running sh test.sh > /dev/null &
單獨使用 nohup
[[email protected] tmp]# nohup sh test.sh > test.out 2>&1
執行後是在前端跑, 若關閉會話, 程序不受影響.
但此時 Ctrl+c
會結束程序.
nohup
+ &
[[email protected] tmp]# nohup sh test.sh &
[2] 112987
[[email protected] tmp]# nohup: 忽略輸入並把輸出追加到"nohup.out"
[[email protected] tmp]#
忽略 Ctrl+c
以及 會話關閉的影響, 程序可以在後臺持續執行.
若會話未關閉, 可通過 jobs -l
檢視當前該程序
[[email protected] tmp]# jobs -l
[1]+ 112987 Running nohup sh test.sh &