cramfs檔案系統製作與移植（二）
阿新 • • 發佈：2018-12-30
[ [email protected] ]#
bootm
## Booting kernel from Legacy Image at 30008000 ...
Image Name: Linux Kernel
Created: 2013-04-23 12:05:15 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2612416 Bytes = 2.5 MiB
Load Address: 30008000
Entry Point: 30008040
Verifying Checksum ... OK
XIP Kernel Image ... OK
OK
OS entry point: 30008040
Image entry point=30008040
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.0.0 (
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: SMDK2440
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
S3C244X: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock3 rootfstype=cramfs init=/linuxrc console=ttyS0,115200
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 59468k/59468k available, 6068k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc4800000 - 0xf6000000 ( 792 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc002f000 ( 156 kB)
.text : 0xc002f000 - 0xc04f3000 (4880 kB)
.data : 0xc04f4000 - 0xc0523c40 ( 192 kB)
.bss : 0xc0523c64 - 0xc05500c4 ( 178 kB)
NR_IRQS:85
irq: clearing pending ext status 00080000
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 201.52 BogoMIPS (lpj=503808)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
gpiochip_add: gpios 288..303 (GPIOK) failed to register
gpiochip_add: gpios 320..334 (GPIOL) failed to register
gpiochip_add: gpios 352..353 (GPIOM) failed to register
NET: Registered protocol family 16
S3C Power Management, Copyright 2004 Simtec Electronics
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
DMA channel 0 at c4804000, irq 33
DMA channel 1 at c4804040, irq 34
DMA channel 2 at c4804080, irq 35
DMA channel 3 at c48040c0, irq 36
S3C244X: Clock Support, DVS off
s3c-adc s3c24xx-adc: attached adc driver
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2440-i2c: slave address 0x10
s3c-i2c s3c2440-i2c: bus frequency set to 98 KHz
s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
Advanced Linux Sound Architecture Driver Version 1.0.24.
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (extended precision)
NTFS driver 2.1.30 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 116
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Console: switching to colour frame buffer device 60x34
fb0: s3c2410fb frame buffer device
s3c2440-uart.0: ttyS0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: ttyS1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: ttyS2 at MMIO 0x50008000 (irq = 76) is a S3C2440
brd: module loaded
loop: module loaded
at24 0-0050: 65536 byte 24c512 EEPROM, writable, 128 bytes/write
physmap platform flash device: 00400000 at 08000000
physmap-flash physmap-flash.0: map_probe failed
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c24xx-nand s3c2440-nand: Tacls=3, 29ns Twrph0=7 69ns, Twrph1=3 29ns
s3c24xx-nand s3c2440-nand: NAND soft ECC
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 221 at 0x000001ba0000
Bad eraseblock 1592 at 0x00000c700000
Creating 11 MTD partitions on "NAND":
0x000000000000-0x000000100000 : "mtdblock0 u-boot 1MB"
0x000000100000-0x000000500000 : "mtdblock1 kernel 4MB"
0x000000500000-0x000000f00000 : "mtdblock2 ramdisk 10MB"
0x000000f00000-0x000001e00000 : "mtdblock3 cramfs 15MB"
0x000001e00000-0x000004600000 : "mtdblock3 jffs2 40MB"
0x000004600000-0x000006e00000 : "mtdblock4 yaffs2 40MB"
0x000006e00000-0x000009600000 : "mtdblock5 ubifs 40MB"
0x000009600000-0x000009700000 : "mtdblock6 info 1MB"
0x000009700000-0x00000bf00000 : "mtdblock7 apps 40MB"
0x00000bf00000-0x00000e700000 : "mtdblock8 data 40MB"
0x00000e700000-0x000010000000 : "mtdblock9 backup 25MB"
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
dm9000 Ethernet Driver, V1.31
eth0: dm9000a at c4864300,c4866304 IRQ 51 MAC: 08:00:3e:26:0a:6b (chip)
usbcore: registered new interface driver rt2800usb
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: S3C24XX OHCI
usb usb1: Manufacturer: Linux 3.0.0 ohci_hcd
usb usb1: SerialNumber: s3c24xx
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for ch341-uart
usbcore: registered new interface driver ch341
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
mousedev: PS/2 mouse device common for all mice
samsung-ts s3c2440-ts: driver attached, registering input device
input: S3C24XX TouchScreen as /devices/virtual/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c-sdi s3c2440-sdi: mmc0 - using pio, sw SDIO IRQ
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: uda134x-hifi <-> s3c24xx-iis mapping ok
ALSA device list:
#0: S3C24XX_UDA134X
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (929 buckets, 3716 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_set: protocol 6
IPVS: Registered protocols (TCP, UDP, AH, ESP)
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: Creating netns size=1008 id=0
IPVS: ipvs loaded.
IPVS: [rr] scheduler registered.
IPVS: [wrr] scheduler registered.
IPVS: [lc] scheduler registered.
IPVS: [wlc] scheduler registered.
IPVS: [lblc] scheduler registered.
IPVS: [lblcr] scheduler registered.
IPVS: [dh] scheduler registered.
IPVS: [sh] scheduler registered.
IPVS: [sed] scheduler registered.
IPVS: [nq] scheduler registered.
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
s3c-rtc s3c2410-rtc: setting system clock to 2023-01-05 16:11:13 UTC (1672935073)
VFS: Mounted root (cramfs filesystem) readonly on device 31:3.
Freeing init memory: 156K
usb 1-1: new full speed USB device number 2 using s3c2410-ohci
usb 1-1: New USB device found, idVendor=05e3, idProduct=0606
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: USB Hub 2.0
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
UBI: attaching mtd8 to ubi8
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: max. sequence number: 12
UBI: attached mtd8 to ubi8
UBI: MTD device name: "mtdblock7 apps 40MB"
UBI: MTD device size: 40 MiB
UBI: number of good PEBs: 320
UBI: number of bad PEBs: 0
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 33
UBI: total number of reserved PEBs: 287
UBI: number of PEBs reserved for bad PEB handling: 3
UBI: max/mean erase counter: 2/1
UBI: image sequence number: 301304821
UBI: background thread "ubi_bgt8d" started, PID 545
UBIFS: mounted UBI device 8, volume 0, name "apps"
UBIFS: file system size: 34965504 bytes (34146 KiB, 33 MiB, 271 LEBs)
UBIFS: journal size: 1806336 bytes (1764 KiB, 1 MiB, 14 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 1651507 bytes (1612 KiB)
UBI: attaching mtd9 to ubi9
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: max. sequence number: 12
UBI: attached mtd9 to ubi9
UBI: MTD device name: "mtdblock8 data 40MB"
UBI: MTD device size: 40 MiB
UBI: number of good PEBs: 319
UBI: number of bad PEBs: 1
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 32
UBI: total number of reserved PEBs: 287
UBI: number of PEBs reserved for bad PEB handling: 3
UBI: max/mean erase counter: 2/1
UBI: image sequence number: 661140379
UBI: background thread "ubi_bgt9d" started, PID 573
UBIFS: mounted UBI device 9, volume 0, name "data"
UBIFS: file system size: 34965504 bytes (34146 KiB, 33 MiB, 271 LEBs)
UBIFS: journal size: 1806336 bytes (1764 KiB, 1 MiB, 14 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 1651507 bytes (1612 KiB)
dm9000 dm9000.0: eth0: link down
dm9000 dm9000.0: eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
Copyright (C) 2012 GuoWenxue<
Default Password: 12345
fulinux login: root
Password:
~ >: ls
apps data home lib media proc stat usr
backup dev info linuxrc mnt root sys var
bin etc init logs opt sbin tmp
~ >: touch xxx
touch: xxx: Read-only file system
~ >:
## Booting kernel from Legacy Image at 30008000 ...
Image Name: Linux Kernel
Created: 2013-04-23 12:05:15 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2612416 Bytes = 2.5 MiB
Load Address: 30008000
Entry Point: 30008040
Verifying Checksum ... OK
XIP Kernel Image ... OK
OK
OS entry point: 30008040
Image entry point=30008040
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.0.0 (
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: SMDK2440
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
S3C244X: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock3 rootfstype=cramfs init=/linuxrc console=ttyS0,115200
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 59468k/59468k available, 6068k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc4800000 - 0xf6000000 ( 792 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc002f000 ( 156 kB)
.text : 0xc002f000 - 0xc04f3000 (4880 kB)
.data : 0xc04f4000 - 0xc0523c40 ( 192 kB)
.bss : 0xc0523c64 - 0xc05500c4 ( 178 kB)
NR_IRQS:85
irq: clearing pending ext status 00080000
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 201.52 BogoMIPS (lpj=503808)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
gpiochip_add: gpios 288..303 (GPIOK) failed to register
gpiochip_add: gpios 320..334 (GPIOL) failed to register
gpiochip_add: gpios 352..353 (GPIOM) failed to register
NET: Registered protocol family 16
S3C Power Management, Copyright 2004 Simtec Electronics
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
DMA channel 0 at c4804000, irq 33
DMA channel 1 at c4804040, irq 34
DMA channel 2 at c4804080, irq 35
DMA channel 3 at c48040c0, irq 36
S3C244X: Clock Support, DVS off
s3c-adc s3c24xx-adc: attached adc driver
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2440-i2c: slave address 0x10
s3c-i2c s3c2440-i2c: bus frequency set to 98 KHz
s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
Advanced Linux Sound Architecture Driver Version 1.0.24.
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (extended precision)
NTFS driver 2.1.30 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 116
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Console: switching to colour frame buffer device 60x34
fb0: s3c2410fb frame buffer device
s3c2440-uart.0: ttyS0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: ttyS1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: ttyS2 at MMIO 0x50008000 (irq = 76) is a S3C2440
brd: module loaded
loop: module loaded
at24 0-0050: 65536 byte 24c512 EEPROM, writable, 128 bytes/write
physmap platform flash device: 00400000 at 08000000
physmap-flash physmap-flash.0: map_probe failed
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c24xx-nand s3c2440-nand: Tacls=3, 29ns Twrph0=7 69ns, Twrph1=3 29ns
s3c24xx-nand s3c2440-nand: NAND soft ECC
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 221 at 0x000001ba0000
Bad eraseblock 1592 at 0x00000c700000
Creating 11 MTD partitions on "NAND":
0x000000000000-0x000000100000 : "mtdblock0 u-boot 1MB"
0x000000100000-0x000000500000 : "mtdblock1 kernel 4MB"
0x000000500000-0x000000f00000 : "mtdblock2 ramdisk 10MB"
0x000000f00000-0x000001e00000 : "mtdblock3 cramfs 15MB"
0x000001e00000-0x000004600000 : "mtdblock3 jffs2 40MB"
0x000004600000-0x000006e00000 : "mtdblock4 yaffs2 40MB"
0x000006e00000-0x000009600000 : "mtdblock5 ubifs 40MB"
0x000009600000-0x000009700000 : "mtdblock6 info 1MB"
0x000009700000-0x00000bf00000 : "mtdblock7 apps 40MB"
0x00000bf00000-0x00000e700000 : "mtdblock8 data 40MB"
0x00000e700000-0x000010000000 : "mtdblock9 backup 25MB"
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
dm9000 Ethernet Driver, V1.31
eth0: dm9000a at c4864300,c4866304 IRQ 51 MAC: 08:00:3e:26:0a:6b (chip)
usbcore: registered new interface driver rt2800usb
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: S3C24XX OHCI
usb usb1: Manufacturer: Linux 3.0.0 ohci_hcd
usb usb1: SerialNumber: s3c24xx
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for ch341-uart
usbcore: registered new interface driver ch341
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
mousedev: PS/2 mouse device common for all mice
samsung-ts s3c2440-ts: driver attached, registering input device
input: S3C24XX TouchScreen as /devices/virtual/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c-sdi s3c2440-sdi: mmc0 - using pio, sw SDIO IRQ
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: uda134x-hifi <-> s3c24xx-iis mapping ok
ALSA device list:
#0: S3C24XX_UDA134X
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (929 buckets, 3716 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_set: protocol 6
IPVS: Registered protocols (TCP, UDP, AH, ESP)
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: Creating netns size=1008 id=0
IPVS: ipvs loaded.
IPVS: [rr] scheduler registered.
IPVS: [wrr] scheduler registered.
IPVS: [lc] scheduler registered.
IPVS: [wlc] scheduler registered.
IPVS: [lblc] scheduler registered.
IPVS: [lblcr] scheduler registered.
IPVS: [dh] scheduler registered.
IPVS: [sh] scheduler registered.
IPVS: [sed] scheduler registered.
IPVS: [nq] scheduler registered.
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
s3c-rtc s3c2410-rtc: setting system clock to 2023-01-05 16:11:13 UTC (1672935073)
VFS: Mounted root (cramfs filesystem) readonly on device 31:3.
Freeing init memory: 156K
usb 1-1: new full speed USB device number 2 using s3c2410-ohci
usb 1-1: New USB device found, idVendor=05e3, idProduct=0606
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: USB Hub 2.0
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
UBI: attaching mtd8 to ubi8
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: max. sequence number: 12
UBI: attached mtd8 to ubi8
UBI: MTD device name: "mtdblock7 apps 40MB"
UBI: MTD device size: 40 MiB
UBI: number of good PEBs: 320
UBI: number of bad PEBs: 0
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 33
UBI: total number of reserved PEBs: 287
UBI: number of PEBs reserved for bad PEB handling: 3
UBI: max/mean erase counter: 2/1
UBI: image sequence number: 301304821
UBI: background thread "ubi_bgt8d" started, PID 545
UBIFS: mounted UBI device 8, volume 0, name "apps"
UBIFS: file system size: 34965504 bytes (34146 KiB, 33 MiB, 271 LEBs)
UBIFS: journal size: 1806336 bytes (1764 KiB, 1 MiB, 14 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 1651507 bytes (1612 KiB)
UBI: attaching mtd9 to ubi9
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: max. sequence number: 12
UBI: attached mtd9 to ubi9
UBI: MTD device name: "mtdblock8 data 40MB"
UBI: MTD device size: 40 MiB
UBI: number of good PEBs: 319
UBI: number of bad PEBs: 1
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 32
UBI: total number of reserved PEBs: 287
UBI: number of PEBs reserved for bad PEB handling: 3
UBI: max/mean erase counter: 2/1
UBI: image sequence number: 661140379
UBI: background thread "ubi_bgt9d" started, PID 573
UBIFS: mounted UBI device 9, volume 0, name "data"
UBIFS: file system size: 34965504 bytes (34146 KiB, 33 MiB, 271 LEBs)
UBIFS: journal size: 1806336 bytes (1764 KiB, 1 MiB, 14 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 1651507 bytes (1612 KiB)
dm9000 dm9000.0: eth0: link down
dm9000 dm9000.0: eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
Copyright (C) 2012 GuoWenxue<
Default Password: 12345
fulinux login: root
Password:
~ >: ls
apps data home lib media proc stat usr
backup dev info linuxrc mnt root sys var
bin etc init logs opt sbin tmp
~ >: touch xxx
touch: xxx: Read-only file system
~ >: