第四章之內存初始化
阿新 • • 發佈：2017-07-31
hold find turn 1-1 col 重新編譯 測試 function rst
1,既然UART可以打印出信息來，那我們可以打印內存中的值。在506行添加如下代碼：
1 2 /***UART transmit function by xu ***/ 3 display_addr_dat: 4 5 ldr r0,[r0] 6 7 ldr r1,=0xE2900020 8 9 ldr r2,=0x30 10 str r2,[r1] @UTXH0=‘0‘ 11 12 ldr r2,=0x78 13 str r2,[r1] @UTXH0=‘x‘ 14 15 ldr r3,=28 16 17 display_loop_count:18 lsr r2,r0,r3 @logical shift right 28 bit 19 and r2,r2,#0xF 20 21 cmp r2,#10 @cmp r2 is mi or pl 10 22 addmi r2,r2,#0x30 @r2 is 1----9 23 addpl r2,r2,#0x37 @r2 is A----F 24 str r2,[r1] 25 26 sub r3,r3,#4 27 cmp r3,#0 28 bpl display_loop_count 29 30 ldr r2,=0xa31 str r2,[r1] @UTXH0=‘\r‘ 32 33 ldr r2,=0xd 34 str r2,[r1] @UTXH0=‘\n‘ 35 36 mov pc, lr
如圖：
2，這樣我們可以進行測試，在216行，進行添加執行代碼，如圖：
我們通過手冊查詢可以得知內存地址oxE000_0000的值為0x43110020。那麽重新編譯和燒寫一下u-boot.bin，看看串口輸
出的信息與我們查詢的值是否相同。
3，接一下來，我們來自己編寫板子的內存初始化代碼，可以根據廠家的光盤中裸機代碼/src/cdram/memory.S中的代碼做相應的
更改。代碼如下：
1 /*** ddrmem initialze by xu***/ 2 .globl ddrmem_init 3 ddrmem_init: 4 5 #define ELFIN_GPIO_BASE 0xE0200000 6 #define APB_DMC_0_BASE 0xF0000000 7 #define DMC_CONCONTROL 0x00 8 #define DMC_MEMCONTROL 0x04 9 #define DMC_MEMCONFIG0 0x08 10 #define DMC_DIRECTCMD 0x10 11 #define DMC_PRECHCONFIG 0x14 12 #define DMC_PHYCONTROL0 0x18 13 #define DMC_PHYCONTROL1 0x1C 14 #define DMC_RESERVED 0x20 15 #define DMC_PWRDNCONFIG 0x28 16 #define DMC_TIMINGAREF 0x30 17 #define DMC_TIMINGROW 0x34 18 #define DMC_TIMINGDATA 0x38 19 #define DMC_TIMINGPOWER 0x3C 20 #define DMC_PHYSTATUS 0x40 21 #define DMC_CHIP0STATUS 0x48 22 #define DMC_AREFSTATUS 0x50 23 #define DMC_MRSTATUS 0x54 24 #define DMC_PHYTEST0 0x58 25 //初始化PHY DLL 26 ldr r0, =APB_DMC_0_BASE 27 //step 2 set PhyControl0.ctrl_start_point PhyControl0.ctrl_inc PhyControl0.ctrl_dll_on bit field to 1 28 ldr r1, =0x0010100A 29 str r1, [r0,#DMC_PHYCONTROL0] 30 31 //step 3 set PhyControl1.ctrl_shiftc PhyControl1.ctrl_ctrl_offsetc 32 ldr r1, =0x00000086 33 str r1, [r0,#DMC_PHYCONTROL1] 34 35 //step 4 set PhyControl0.ctrl_start bit-field to 1 DLL on 36 ldr r1, =0x0010100B 37 str r1, [r0,#DMC_PHYCONTROL0] 38 39 find_lock_val: 40 //step 11 loop until DLL is locked 41 ldr r1, [r0,#DMC_PHYSTATUS] 42 and r2, r1,#0x7 43 cmp r2, #0x7 44 bne find_lock_val 45 46 //setp 12 Force value looking 47 and r1, #0x3fc0 48 mov r2, r1, LSL #18 49 orr r2, r2, #0x100000 50 orr r2, r2, #0x1000 51 orr r1, r2, #0xB 52 str r1, [r0,#DMC_PHYCONTROL0] 53 54 //初始化DMC0 55 //step 5 set ConControl 56 ldr r1, =0x0FFF1010 57 str r1, [r0,#DMC_CONCONTROL] 58 59 //step 6 set MemControl 60 ldr r1, =0x00202400 61 str r1, [r0,#DMC_MEMCONTROL] 62 63 //step 7 set MemConfig0 512M config,8 banks 64 ldr r1, =0x20E00323 65 str r1, [r0,#DMC_MEMCONFIG0] 66 67 //step 8/1 set PrechConfig 68 ldr r1, =0xFF000000 69 str r1, [r0,#DMC_PRECHCONFIG] 70 71 //step 9/1 set TimingAref t_refi=7.5us * 133MHz=1038(0x40E) 72 ldr r1, =0x0000040E 73 str r1, [r0,#DMC_TIMINGAREF] 74 //step 9/2 set TimingRow tRAS=45ns tRC=60ns tRCD=15ns tRP=15ns tRRD=7.5ns tRFC=127.5ns 75 ldr r1, =0x11122206 76 str r1, [r0,#DMC_TIMINGROW] 77 //step 9/3 set TimingData tWTR=7.5ns tWR=15ns tRTP=7.5ns cl=4 78 ldr r1, =0x12140000 79 str r1, [r0,#DMC_TIMINGDATA] 80 //step 9/4 set TimingPower t_mrd>=tMRD=2nCK t_cke<=tCKE=3nCK t_xp>=tXP=2nCK tXSRD=200ns tFAW=35ns 81 ldr r1, =0x05DC0343 82 str r1, [r0,#DMC_TIMINGPOWER] 83 84 //初始化DDR2 DRAM 85 //step 14 lssue a "NOP" for DirectCmd and hold CKE to high level 86 ldr r1, =0x07000000 87 str r1, [r0,#DMC_DIRECTCMD] 88 89 //step 16 lssue a "PALL" for DirectCmd 90 ldr r1, =0x01000000 91 str r1, [r0,#DMC_DIRECTCMD] 92 93 //step 17 lssue an "EMRS2" for DirectCmd 94 ldr r1, =0x00020000 95 str r1, [r0,#DMC_DIRECTCMD] 96 97 //step 18 lssue an "EMRS3" for DirectCmd 98 ldr r1, =0x00030000 99 str r1, [r0,#DMC_DIRECTCMD] 100 101 //step 19 lssue an "EMRS" for DirectCmd and enable DLLs enable DQS 102 ldr r1, =0x00010000 103 str r1, [r0,#DMC_DIRECTCMD] 104 105 //step 20 lssue a "MRS" for DirectCmd and reset DLL 106 ldr r1, =0x00000542 107 str r1, [r0,#DMC_DIRECTCMD] 108 109 //step 21 lssue a "PALL" for DirectCmd 110 ldr r1, =0x01000000 111 str r1, [r0,#DMC_DIRECTCMD] 112 113 //step 22 lssue two "Auto Refresh" for DirectCmd 114 ldr r1, =0x05000000 115 str r1,[r0,#DMC_DIRECTCMD] 116 117 ldr r1, =0x05000000 118 str r1,[r0,#DMC_DIRECTCMD] 119 120 //step 23 lssue a "MRS" for DirectCmd and without reseting DLL 121 ldr r1, =0x00000442 122 str r1, [r0,#DMC_DIRECTCMD] 123 124 //step 25 lssue an "EMRS" for DirectCmd set OCD Calibration Default and exit OCD Calibration 125 ldr r1, =0x00010380 126 str r1, [r0,#DMC_DIRECTCMD] 127 128 ldr r1, =0x00010000 129 str r1, [r0,#DMC_DIRECTCMD] 130 131 //step 27 set ConControl and turn on "auot refresh" 132 ldr r1, =0x0FF01030 133 str r1, [r0,#DMC_CONCONTROL] 134 135 //step 8/2 set PwrdnConfig 136 ldr r1, =0xFFFF00FF 137 str r1, [r0,#DMC_PWRDNCONFIG] 138 139 //step 28 IF power down modes is required set MemControl 140 ldr r1, =0x00202400 141 str r1, [r0,#DMC_MEMCONTROL] 142 143 //putout URAT char "DDR IS OK!" 144 ldr r0, =0xE2900020 145 ldr r1, =0x44 @UTH=‘D‘ 146 str r1, [r0] 147 148 ldr r1, =0x44 149 str r1, [r0] @UTH=‘D‘ 150 151 ldr r1, =0x52 152 str r1, [r0] @UTH=‘R‘ 153 154 ldr r1, =0x20 155 str r1, [r0] @UTH=‘ ‘ 156 157 ldr r1, =0x49 158 str r1, [r0] @UTH=‘I‘ 159 160 ldr r1, =0x53 161 str r1, [r0] @UTH=‘S‘ 162 163 ldr r1, =0x20 164 str r1, [r0] @UTH=‘ ‘ 165 166 ldr r1, =0x4f 167 str r1, [r0] @UTH=‘O‘ 168 169 ldr r1, =0x4b 170 str r1, [r0] @UTH=‘K‘ 171 172 ldr r1, =0x21 173 str r1, [r0] @UTH=‘!‘ 174 175 ldr r1, =0xa 176 str r1, [r0] @UTXH0=‘\r‘ 177 178 ldr r1, =0xd 179 str r1, [r0] @UTXH0=‘\n‘ 180 181 mov pc, lr
4，在UART執行代碼下面添加內存初始化執行代碼220-221行。如圖：
5，內存初始化完成，但是我們不知道內存初始化是否正確，這就需要驗證。通過內存讀取數據代碼來進行驗證222行-225行。如圖所示：
6，然後，進行make,燒寫u-boot.bin.然後可以看到串口輸出信息中，輸出與我們輸入相同的內存地址的值
第四章之內存初始化